Safe Work with Antineoplastic Drugs: Exposure, CSTD, PPE and Spill Management

Antineoplastic and other hazardous drugs can affect staff during preparation, transport, administration, cleaning and waste handling. [2][4] Exposure happens through skin and mucous membrane (including eye) contact, inhalation, hand-to-mouth contact and sharps injury. [2] This guide describes general principles; your facility's written procedure always comes first. [6][10]

This guide is for nurses and pharmacy staff. It does not describe patient care or a patient procedure. It focuses on staff safety.

Your facility's procedure comes first. This guide collects general principles. Your facility's written procedure, the instructions of the spill kit and the manufacturer's instructions for use come before this guide. [6][10] If you see a conflict, ask the responsible unit in your facility.

Are antineoplastic drugs and hazardous drugs the same thing?

No. Antineoplastic drugs are used in cancer treatment and are a subset of hazardous drugs. [1] The NIOSH list of hazardous drugs does not consist of antineoplastics only. It also covers other drugs that meet the hazard criteria. [1]

So do not use the two terms as synonyms. Your facility's own drug list decides which drug counts as hazardous. [2][4] The NIOSH list does not replace this inventory. [1][2]

The sources use the terms "antineoplastic", "cytotoxic" and "chemotherapy drug". This guide uses these terms as the sources use them. [9][10]

How does exposure happen?

The main routes are skin and mucous membrane (including eye) contact and inhalation. [2][3] Hand-to-mouth contact and accidental injection, such as a needle stick, are also possible. [2][3]

Five exposure routes around a drug vial and bag: skin and eye contact, contaminated surface, airborne particles, hand-to-mouth contact and needle stick. skin and eye contact contaminated surface needle stick airborne particles (inhalation) hand-to-mouth

Exposure does not happen only while preparing a drug. Contaminated surfaces, equipment, textiles and patient excreta are also sources of contact. [2][6] So staff who transport and administer the drug, clean surfaces and manage waste are also part of the risk assessment. [2]

The chance of exposure depends on these factors: [2]

  • The form of the drug.
  • The route of exposure.
  • How often and how long the contact lasts.
  • Work practices (the way the task is done).
  • The controls and PPE in place.

The risk from vapor, aerosol, droplets and dust differs by drug and by task. [2] Not all drugs and tasks carry the same risk. [2]

Which stages does safe handling cover?

It covers the whole workflow, from receiving the drug to removing its waste. [4][2] Receiving, storage, preparation, dispensing, administration and waste management are parts of this workflow. [4] Cleaning contaminated surfaces is also part of the workflow. [2]

Do not rely on a single device or a single protective measure. Engineering controls, work practices and PPE are used together. [8][2]

Five nested protection layers: training and procedure, safe workflow, engineering controls, closed transfer and personal protective equipment. training and procedure safe workflow engineering controls closed transfer (CSTD) PPE Layers are used together.

No single layer gives full protection on its own. A CSTD does not replace ventilated preparation equipment or a correct work procedure. [8][2]

What should I know before I start a task?

You should know your facility's hazardous drug list, the risk assessment for your task and the related written procedures. [2][4]

Training and written procedures should cover these topics: safe handling, spill response, waste management and where to turn after an exposure. [6][7] The 2024 ASCO/ONS standards require written administration safety standards by route of administration and care setting. [7] ISOPP recommends annual training and keeping a training record. Your facility's procedure sets the frequency. [6]

Check these before you start:

  1. Have you had the facility training? [6]
  2. Is the work area suitable? [2][4]
  3. Are the PPE and the transfer set ready? [2][4]
  4. Is the spill kit in place and complete? [2][4]

If you are pregnant, breastfeeding or planning a pregnancy, do a personal risk assessment with your workplace health unit. [2] Risk management is considered for all staff, not only for staff known to be pregnant. [2] This assessment and your facility's procedure decide who can work in which task.

What is a closed system drug transfer device (CSTD), and what is it for?

A CSTD aims to mechanically block the escape of drug or vapor to the outside during transfer. [8] It also aims to block contamination from the environment from entering the system. [8]

Closed transfer diagram of a vial, a closed connection part and a syringe or bag; escape to the outside is blocked. syringe or bag closed connection escape out blocked vial

A CSTD does not prevent exposure completely. It also does not remove the need for gloves and gowns. [8][2] NIOSH lists CSTDs and PPE as separate control elements. [2]

For the steps of use, follow the manufacturer's instructions and your facility's procedure. Use all the connections and components of the system together. Not every system is compatible with every drug. [5]

For more detail, see the CSTD product page.

Is it mandatory to use a CSTD?

The sources this guide is based on contain no general CSTD requirement for Türkiye. The US standard USP <800> recommends a CSTD for preparation but does not make it mandatory. [5] For administering the drug to the patient, it considers a CSTD necessary for some antineoplastics. [5]

According to USP <800>, when the drug is given to the patient (administration), a CSTD is considered necessary for the antineoplastics in Table 1 of the NIOSH list, if the dosage form allows it. [5] USP states that a CSTD that is incompatible with the drug must not be used. [5]

USP is a US standard. It cannot be presented as a direct legal requirement in Türkiye. [4] At which stage your facility uses a CSTD depends on the drug, the dosage form, compatibility and your facility's procedure. [5]

Which personal protective equipment (PPE) should I use?

PPE is chosen according to your task and the possible risk of splash, aerosol or spill. [2] Your facility's risk assessment decides which PPE is needed. [2]

The NIOSH control approach includes these items: [2]

  • Double chemotherapy gloves (for tasks with high exposure).
  • A disposable, impermeable gown.
  • Eye and face protection when needed.
  • Hair, sleeve and shoe protection when needed.
  • Respiratory protection when needed.

A surgical mask is not respiratory protection against every aerosol or vapor risk. The choice of respirator and the fit test depend on your facility's respiratory protection program. [2]

In a spill response, wear the protective equipment listed in the instructions of the spill kit. [2][6] Depending on the type of spill, the mask or respirator, goggles and shoe covers may change. [6]

What should I do if a spill happens?

First warn the people nearby, restrict the area and call for trained help. [6][10] If you do not have the training or the kit, do not respond to the spill yourself. [6][11]

WARNING: If the spill is beyond your spill training or the capacity of the kit, do not try to clean it up yourself. Clear the area, block the entrance and start your facility's emergency response procedure. [6][2][11]

The order below is compiled from the sources. The instructions of the kit and of your facility may change the order. One hospital instruction covers the liquid with an absorbent pad before putting on PPE. [10]

  1. Warn the people nearby. Move unexposed people away. [6][10]
  2. Restrict the area with a warning sign. Prevent unauthorized entry. [6][10]
  3. Ask the trained spill response team for help. Bring the kit. [6][10]
  4. Put on your PPE according to the instructions of the kit. [6][10]
  5. Identify the type of spill. Cover the liquid with absorbent material. For powder, follow the instructions of the kit. [6][10]
  6. Start cleaning from the outside toward the center. [6]
  7. After you remove the visible contamination, clean the surface with detergent and rinse with water. [6]
  8. Remove your PPE from the outside. Put the materials you used and the PPE into the proper waste container. Seal the waste. [6][10]
  9. Wash your hands. [6][10]
  10. Record the event and restock the kit. [6][10]
Spill response flow: warn, restrict the area, call for help, put on PPE; separate branches for liquid and powder; clean from the outside to the center, seal the waste, record. The kit and facility instructions come first. 1 warn 2 restrict area 3 call for help and get the kit 4 put on PPE liquid: cover with absorbent material powder: cover gently, no dust 5 clean outside to center 6 clean with detergent, rinse with water 7 seal the waste 8 wash hands 9 record, restock kit

The sources give different methods for a powder spill. The ISOPP sample procedure describes covering the powder gently. [6] One hospital instruction asks to wipe the powder with a wet pad. [10] So follow the instructions of your kit and your facility.

The instruction of one university hospital is a local example. It is not a standard protocol for all facilities. [10] Kit steps may differ from one facility to another.

For information about spill kits, see the spill kit product page.

What should I do after skin contact, eye contact or a needle stick?

Remove contaminated clothing and PPE. Wash the affected area right away and start your facility's exposure procedure. [10][6][11]

First response for skin, eye and needle stick: remove clothing, wash the area, report the event, start the facility's exposure procedure. Skin Eye Needle stick remove clothing soap and water eyewash station possible exposure report start facility exposure procedure employee health

Skin contact. Remove contaminated clothing. Wash the skin with soap and water. [10][11]

Eye contact. Rinse the eye right away with plenty of water or a suitable eyewash solution. Ask for a medical assessment. [10][11]

Needle stick. A needle stick or sharps injury is a possible exposure event. Report the event without delay. Go to an employee health assessment. [2][6]

Suspected inhalation. Report the event without delay and go to your facility's employee health process. [6]

The length of washing differs by source. One hospital instruction states that the eye is rinsed for at least 15 minutes. [10] An Ontario guideline recommends that skin washing last 15 minutes. [11] Your facility's procedure may give a different time or order. Follow your facility's time.

EMERGENCY: In an acute exposure, start your facility's emergency response and employee health procedure right away. [6][10] If you need fast medical help, call your facility's emergency line, or call 112 (or your local emergency number) right away.

The sources this guide is based on do not give a common symptom or exposure level that requires a 112 call. Your facility's emergency system and employee health unit are the basis.

What should I record after an exposure?

Document the event in your facility's incident reporting and employee health record system. [6] The record should include the event, the drug involved, the action you took and the follow-up information. [6]

Also record spills and corrective actions. [6] For how long to keep records, follow your facility's procedure and local law. [6] This guide does not give a fixed period.

It would not be right to say that a single exposure will certainly cause a health outcome. The sources describe the hazard and the occupational risks, but they do not give a certain individual outcome. [2][3]

How is waste sorted?

Drug-contaminated waste, PPE and equipment are managed in a defined, separate and safe way, from the place where they are produced to disposal. [6][4] They are sorted, sealed and transported according to your facility's hazardous drug waste procedure. [6]

Three separate streams for drug-contaminated material, sharps waste and general waste; sorting follows the facility's waste plan. drug- contaminated material sharps waste general waste Sorting follows facility waste plan.

Do not put all waste in the same container. Sharps waste and genotoxic waste are separated according to your facility's procedure and the regulation. [6][9]

ISOPP recommends following local, regional and national regulations in waste management. [6] The container color, code and brand depend on your facility's waste plan. This guide does not give a container color or code.

Do patient urine and stool create a risk?

Patient excreta are a possible source of contact. [2] The Medical Waste Control Regulation of Türkiye defines waste that contains cytotoxic and antineoplastic products used in cancer treatment as genotoxic waste. [9] The excreta of patients treated with these agents, such as urine and stool, fall under the same definition. [9]

How long contamination lasts differs by drug and by facility. This guide does not give a single time for all antineoplastics. [2][9]

Which regulation applies in Türkiye?

The definition of genotoxic waste is in article 4, paragraph (g) of the Medical Waste Control Regulation of Türkiye. For staff safety, there is a reference to the Ministry's antineoplastic guide; the current version of this guide is not among the sources this guide is based on. [9][12] Check the current amendments to the regulation and your facility's approved waste plan. [9]

A Ministry of Health hospital page that reproduces the Patient and Employee Safety Regulation refers to the related antineoplastic safe handling guide. [12] The current, official copy of the Ministry's guide is not among the sources this guide is based on. Details in archive copies are not presented as a current requirement.

A single, general requirement for a CSTD or a spill kit for every health facility in Türkiye is not found in the official sources this guide is based on. Follow your facility's current procedure.

Questions you can ask your nurse

  1. Which is our facility's hazardous drug list, and where is the risk assessment for my task?
  2. Where is the current version of the spill, exposure and waste procedures? When do I get the training?
  3. At which stages do we use a CSTD? With which drugs is our CSTD compatible?
  4. What PPE does my task need? If a respirator is needed, who does the fit test?
  5. Where is the spill kit, and when is its content checked? How do we define a small and a large spill?
  6. If skin contact, eye contact or a needle stick happens, whom do I report to, and with which form? How do I reach the employee health unit?
  7. If I am pregnant, breastfeeding or planning a pregnancy, who does the personal risk assessment?
  8. What does our waste plan say about the excreta of patients receiving chemotherapy and about drug-contaminated waste? Where does sharps waste go?
  9. Where are incident records kept? How long are they kept?

Frequently asked questions

What do you do if a chemotherapy drug is spilled?

Warn the people nearby, restrict the area and call for trained help. [6][10] If you do not have the training or the kit, do not respond yourself. [6][11] Start cleaning according to the instructions of the kit and your facility. [6][10]

How is a spill kit used?

Follow the written instructions inside the kit and your facility's procedure. [6][10] Put on your PPE and use the absorbent material that suits the type of spill. [6][10] One hospital instruction is a local example. [10]

Is water used on a powder spill?

The instructions of the kit and your facility decide. The ISOPP sample procedure describes covering the powder gently, and one hospital instruction describes wiping it with a wet pad. [6][10] No single method is recommended for everyone.

What is a closed system drug transfer device, and what is it for?

A CSTD aims to mechanically block the escape of the drug or its vapor to the outside, and the entry of contamination from the environment into the system, during transfer. [8] It does not provide zero exposure. [8][2]

Is a CSTD mandatory when preparing drugs?

USP <800> recommends a CSTD for preparation but does not make it mandatory. [5] This is a US standard. The sources this guide is based on contain no general requirement for Türkiye. [5]

Is a CSTD mandatory when giving chemotherapy?

According to the USP <800> FAQs, a CSTD is required for the antineoplastics in Table 1 of the NIOSH list if the dosage form allows it. [5] This is a provision of the US standard. [4][5]

Does a CSTD replace gloves and gowns?

No. A CSTD, engineering controls and PPE are separate control layers. [2][8] They are applied together according to the drug and the task. [2]

What are the exposure routes when working with antineoplastic drugs?

The main routes are skin and mucous membrane (including eye) contact and inhalation. [2][3] Hand-to-mouth contact and needle sticks are also possible. [2][3]

What should I do if the drug splashes on my skin?

Remove contaminated clothing and wash the skin with soap and water. [10][11] Report the event and start your facility's exposure procedure. [6][10]

What should I do if the drug splashes in my eye?

Rinse the eye right away with plenty of water or an eyewash solution and ask for a medical assessment. [10][11] One hospital instruction states at least 15 minutes of rinsing. [10] Follow your facility's time.

Whom should I tell if I have a needle stick?

Report the event without delay and go to an employee health assessment. [2][6] Use the reporting point set by your facility. This guide does not give a name or a phone number.

Where do contaminated gloves and sets go?

Waste that contains an antineoplastic product falls under the genotoxic waste definition. [9] Your facility's waste plan decides which waste class gloves and sets fall into. [6] For sharps, follow the related container and procedure.

About this guide

Melekırmak prepared this guide. It is based on international standards and official occupational health guidance. It does not replace your facility's procedure. Melekırmak is the distributor in Türkiye of some of the medical devices used in the procedures described in this guide.

Published:
Last updated:

Sources

Back to Knowledge Centre